Sound Systems For Medium Sized Models

Here are a selection of sound system kits to suit medium size RC models, e.g. aircraft between 50 - 72inch wingspan. Installation is very easy and our 4inch loudspeakers provide the very best possible sound quality for your RC or static model.

What's New:

May 14, 2021

New Hercules AC130 gunship sound set now available bringing our total airplane sound sets to 120.

February 17, 2021

New Airbus A380 sound set now available bringing our total airplane sound sets to 119.

January 26, 2021

New 5.1.1 release of ShockWave 3 firmware and Software. Exciting new features - Afterburner light controller + automatic sync. with Afterburner sound and much more.

January 06, 2021

New Aero Vodochody L39 Albatros Jet Trainer sound set now available bringing our total airplane sound sets to 118.

January 01, 2021

New Article - Integrating Afterburner Light Sets with ShockWave 3.

August 01, 2020

USB SD/microSD card reader now included with ShockWave 3 sound module and all ShockWave 3 sound systems.

ShockWave® 3 Sound Systems For Medium Models

The Wingspan size mentioned above is a general guideline only. Please make sure that your own model can accomodate the loudspeakers referenced on this page. Larger loudspeakers will always sound better than smaller ones if your model can accomodate them.

Also see: Sound Systems For Larger Size Models and | Sound Systems For Smaller Models

Quick-Start Guide

ShockWave 3-System 1 x 2 inch x 4 Ohm-Exciter
WELL SUITED TO FOAM MODELS

Notes on Mounting Exciters.

Item Number : ShockWave3-1x2x4EX
Voltage : 4.5 - 14 Volts (3S LiPo), 2 Amps maximum.
Power Output : 20 Watts at 12 Volts
Contents :
1 x ShockWave 3 Sound Module
1 x Pre-loaded microSD card
1 x USB 2.0 SD/microSD card reader
1 x 2inch 20 Watt 4 Ohm Exciter
1 x Male-Male-Female Y Servo Lead for one throttle input.
1 x Male-Male Servo Lead for one gun/horn/bell input.
4ft x Twisted red/black 22AWG wire
Weight : 200 grams (6.45oz)

USD$179.99

ONLY Canadian and US Customers
can use the Add To Cart Button.
For all other countries please email us at contactus@modelsoundsinc.com for a shipping quote.

See our amazing new DopplerFX accessory board here.

This sound system kit contains everything you need to easily install great sound in your medium sized airplane, helicopter, boat or tank models.

The ShockWave 3 sound module includes all our pre-configured Aircraft or Helicopter or Boat or Tank sound sets.

The 4ft of red/black twisted wire is used for both loudspeaker and power connections. You will need to provide and solder battery connectors of your choice and solder the provided wires to the exciters.

Recommended power supply - 5S LiPo.

This system uses one 2inch holeless Exciter instead of a conventional loudspeaker. Exciters work by vibrating the surface to which they are attached. It may be attached to a flat surface (using the self-adhesive double side tape ring) to the inside of your airplane/helicopter fuselage, boat or tank hull etc. without cutting holes for a conventional loudspeaker. It is small and light weight.

The sound it produces, both volume and tone, is variable and depends on the type of material to which it is attached. Factors such as type of material, (wood, fibreglass, foam etc.), stiffness, thickness, all play significant roles in determining the volume and quality of the sound.

Thinner, more flexible, materials will produce more sounds and will tend to emhpasize the higher, treble frequencies. Thicker and stiffer materials will be quieter but will produce better low frequency bass sounds.

Dense aircraft foam between 3-5mm (about 1/8inch to 3/16inch) thick works well so try to find an area in your model that has this thickness and is flat.

Click on the links above for details of the individual components.

If you want to change any of the many configurable options or switch the sounds around or add or delete sounds yourself, you should purchase the optional Windows 10/8.1/8/7 ShockWave 3 PC Software here.

Quick-Start Guide

ShockWave 3-System 1 x 4 inch x 4 Ohm
SUPERB SOUND QUALITY
GOOD FOR WOODEN AND LARGE FOAM MODELS

Notes on Mounting Loudspeakers.

Item Number : ShockWave3-1x4x4
Voltage : 4.5 - 13 Volts (3S LiPo), 2 Amps maximum.
Power Output : 20 Watts at 13 Volts
Contents :
1 x ShockWave 3 Sound Module
1 x Pre-loaded microSD card
1 x USB 2.0 SD/microSD card reader
1 x 4inch 20 Watt 4 Ohm Loudspeaker
1 x Male-Male-Female Y Servo Lead for one throttle input.

1 x Male-Male Servo Lead for one gun/horn/bell input.

4ft x Twisted red/black 22AWG wire
Weight : 203 grams (7.2oz)

USD$179.99

ONLY Canadian and US Customers
can use the Add To Cart Button.
For all other countries please email us at contactus@modelsoundsinc.com for a shipping quote.

See our amazing new DopplerFX accessory board here.

This next to top-of-the-line sound system kit contains everything you need to easily install superb quality sound in your medium sized airplane, helicopter, boat or tank models.

The ShockWave 3 sound module includes all our pre-configured Aircraft or Helicopter or Boat or Tank sound sets.

The 4ft of red/black twisted wire is used for both loudspeaker and power connections. You will need to provide and solder battery connectors of your choice and solder the provided wires to the loudspeaker.

Recommended power supply - 3S LiPo.

Click on the links above for details of the individual components.

If you want to change any of the many configurable options or switch the sounds around or add or delete sounds yourself, you should purchase the optional Windows 10/8.1/8/7 ShockWave 3 PC Software here.

Quick-Start Guide

ShockWave 3-System 1 x 3.3 inch x 4 Ohm
GOOD SOUND QUALITY
SMALLER, WATER RESISTANT SPEAKER

Notes on Mounting Loudspeakers.

Item Number : ShockWave3-1x3x4
Voltage : 4.5 - 13 Volts (3S LiPo), 2 Amps maximum.
Power Output : 20 Watts at 13 Volts
Contents :
1 x ShockWave 3 Sound Module
1 x Pre-loaded microSD card
1 x USB 2.0 SD/microSD card reader
1 x 3.3inch 20 Watt 4 Ohm Loudspeaker
1 x Male-Male-Female Y Servo Lead for one throttle input.
1 x Male-Male Servo Lead for one gun/horn/bell input.
4ft x Twisted red/black 22AWG wire
Weight : 290 grams (9.4oz)

USD$179.99

ONLY Canadian and US Customers
can use the Add To Cart Button.
For all other countries please email us at contactus@modelsoundsinc.com for a shipping quote.

See our amazing new DopplerFX accessory board here.

This sound system kit contains everything you need to easily install good quality sound in your medium sized airplane, helicopter, boat or tank models.

The ShockWave 3 sound module includes all our pre-configured Aircraft or Helicopter or Boat or Tank sound sets.

A feature of this kit is the 3.3inch loudspeaker with a waterproof cone making it ideal for model boats. This loudspeaker is heavier at 240 grams than our standard 4inch model at 162 grams but can still be used in model aircaft where space is at a premium if the model's payload capacity is high enough.
The 4ft of red/black twisted wire is used for both loudspeaker and power connections. You will need to provide and solder battery connectors of your choice and solder the provided wires to the loudspeaker.

Recommended power supply - 3S LiPo.

Click on the links above for details of the individual components.

If you want to change any of the many configurable options or switch the sounds around or add or delete sounds yourself, you should purchase the optional Windows 10/8.1/8/7 ShockWave 3 PC Software here.